CADDX NX-6 Instalační manuál stáhnout pdf (Strana 52)

GE Security

LOCATION 40 - SYSTEM TIMERS (14 segments, numerical data)

Location 40 contains the duration of various system timing functions. Example: If you

want the duration of the dynamic battery test to be 30 minutes, you should program [3]-

[0]-[*] in segment 1 of this location. The [3]-[0] is the number of minutes; the [*] stores the

data, and moves to the next segment of this location.

Segment 1

Dynamic battery test duration in minutes, 0-255 minutes (“0” = no test)

Segment 2

AC fail report delay in minutes, 0-255 minutes

Segment 3

Power up delay in seconds, 0-60 seconds (“0” = no power up delay)

Segment 4

Siren time in minutes, 1-255 minutes

Segment 5 Telephone line cut delay in seconds, 0-255 seconds (“0” = no

telephone line monitoring enabled)

Segment 6

Cross zone time in minutes, 0-255 (“0” = no cross zoning)

Segment 7 Chime time in 50 msec. (1/ 20th second) increments from 0-12

seconds (“0” = follows zone 255 latched)

Segment 8

Dial delay in seconds, 0-255 seconds (0 no abort delay)

Segment 9 Fire alarm verification time in seconds, 120-255 seconds (“0” = no fire

alarm verification). Values less than 120 sec. are considered as 120

sec.

Segment 10

Listen-in time in seconds, 0-255 (“ 0” = no listen-in time)

Segment 11 Zone activity monitor feature timed in hours/days, 0-255 (“0” =

disabled)

Segment 12

Auto arming warning timer, 1-255 minutes

Segment 13

Auto arming retry timer, 1-255 minutes

Segment 14

Reserved

LOCATION 41 - CODE REQUIREMENTS (1 segment, feature data)

Segment 1

1 =

On: enables the 6-digit code option. If 6-digit option is enabled, all

arm/disarm codes and the “Go To Program Code” are 6 digits. If

this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5]-

[6]. NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE

“GO TO PROGRAM CODE” IS A SIX-DIGIT CODE BEFORE

YOU EXIT FROM PROGRAMMING

2 =

On: requires code entry for [*]-[9]-[8] (perform callback download)

and [*]-[9]-[9] (answer incoming call for download) functions

3 = Reserved

4 = Reserved

5 = On: keypad shutdown mode

6 = On: user authorisation to enter program mode

7 = On: codes 16 and 17 are guard codes

8 = Reserved

LOCATION 42 - GO TO PROGRAM CODE (6 segments, numerical data)

Location 42 contains the “Go To Program Code”. This location contains a code with either

4 or 6 digits. If the 6-digit code option is enabled in Location 41, THIS CODE MUST

CONTAIN SIX (6) DIGITS. If this option is not enabled in location 41, the last 2 segments

(digits) will be ignored. With the NX-6 disarmed, the “Go To Program Code” can be used

to enter the Program Mode.

NX-6-EUR Installation manual Page 52 23/12/04

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 103 104

Komentáře k této Příručce

Žádné komentáře

CADDX NX-6 Instalační manuál Strana 52

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu CADDX NX-6