CADDX NX-8e Specifikace Strana 34
- Strana / 80
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
NX-8E CONTROL
32
LOCATION 103 - PARTITION 6 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 103 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit Time 1: Exit time that will be used for all zones designated as Delay 1.
Segment 3, Entry Time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Segment 4, Exit Time 2: Exit time that will be used for all zones designated as Delay 2.
Segments 5 & 6: Reserved
LOCATION 104 - ACCOUNT CODE FOR PARTITION 7 (6 segments, numerical data)
The account code sent when partition 7 is reported is programmed in location 104. If location 104 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 105 - PARTITION 7 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 105 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 106 - PARTITION 7 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 106 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit Time 1: Exit time that will be used for all zones designated as Delay 1.
Segment 3, Entry Time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Segment 4, Exit Time 2: Exit time that will be used for all zones designated as Delay 2.
Segments 5 & 6: Reserved
LOCATION 107 - ACCOUNT CODE FOR PARTITION 8 (6 segments, numerical data)
The account code sent when partition 8 is reported is programmed in location 107. If location 107 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 108 - PARTITION 8 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 108 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 109 - PARTITION 8 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 109 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds.
If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit Time 1: Exit time that will be used for all zones designated as Delay 1.
Segment 3, Entry Time 2: Entry time that will be used when a Delay 2 zone type initiates an entry Delay.
Segment 4, Exit Time 2: Exit time that will be used for all zones designated as Delay 2.
Segments 5 & 6: Reserved
- Series 1
- SAFETY SYMBOL LEGEND 2
- Table of Contents 3
- ORDERING INFORMATION 4
- I. GENERAL DESCRIPTION 5
- II. BOARD INSTALLATION 5
- III. GLOSSARY 6
- NX-8E CONTROL 10
- V. PROGRAMMING THE CONTROL 12
- (Feature Selection Data) 13
- L QUICK START INSTALLATION 14
- X. PROGRAMMING LOCATIONS 15
- NOTE: Must 24
- Default is OFF 44
- XII. PROGRAMMING WORKSHEETS 47
- 62
- XIII. NX-8E WIRING DIAGRAM 68
- XIV. TERMINAL DESCRIPTIONS 69
- XV. APPENDIX 1 71
- XVI. APPENDIX 2 72
- XVII. APPENDIX 3 73
- XVIII. APPENDIX 4 74
- INDUSTRY CANADA INFORMATION 75
- XX. NOTICES 76
- Hochiki: SBC-4/12, 4/12W 77
- CURRENT 78
- STANDBY BATTERY 78
- CAPACITY 78
- ALARM CURRENT 78
- XXIII. SPECIFICATIONS 80
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu CADDX NX-8e
(42 stránky)Belkin F5L144EDWHT-C00 manuales
Manuales del propietario y guías del usuario para Casos de tabletas Belkin F5L144EDWHT-C00.
Ofrecemos 1 manuales en pdf Belkin F5L144EDWHT-C00 para descargar gratis por tipos de documentos: Ficha de datos
Komentáře k této Příručce